Wi-CAT LLC

Wireless Comprehensive Advanced Technology. Build your network now.

Wi-CAT LLC
Навигация Форума
Вы должны войти, чтобы создавать сообщения и темы.

Режим WDS на AIR-DUO-G

termit
termit@termit
52 Сообщения
#1 · 13/08/2020, 22:05

Здравствуйте!

Имеем схему (см рисунок). Роутеры R1 и R2 обновлены до текущей (11.08.2020) версии, настройки сброшены. Далее, сделаны минимальные настройки для проверки режима WDS, а именно заданы ip адреса: у первого 192.168.2.1 , у второго 192.168.2.2; задан ключ wifi (11111111); оба переведены в режим AP-bridge; в настройках WDS задан диапазон 5ГГц, ключ AES (88888888) и у первого режим LAZY, у второго режим REPITER,  и указан BSID 5ГГц первого. Так как роутеры пока к локалке не подключены, адреса от dhcp они не получают, и используют адреса, что заданы у них в настройке LAN. Конфиги прилагаю.

Результат: WDS не работает. (Проверяю разъединением шнура между роутерами, и пингом обоих роутеров - пинг с ноута проходит только до ближайшего в цепочке роутера, также смотрю в интерфейсах - интерфейса wds0 нет, в журналах обоих нет ничего про wds, пардон, что-то есть).

Проверялось двумя ноутами, с подключением по эзернет, ip - static. Почему двумя:  при изменении на роутерах вроде-бы безобидных настроек(не связанных с их ip адресами, например настройка диапазона на вкладке wds), роутеры после применения настроек не просто не пускают в UI, а даже не пингуются (оба). При этом, ноуты, подключенные через них (как на схеме), друг друга пингуют. Лечиться это только выкл/вкл роутеров. Ни вытыкание кабеля из ноута и его переподключение, ни перезагрузка ноута, ни диагностика подключения (очистка арп и тд, что она там делает) - не помогает. Вот для проверки того, что ноут не причём, был подключен второй ноут. После перезагрузки роутеров, пинг до них восстанавливается, UI работает, и мы видим, что настройки. изменённые на предыдущей итерации сохранены. Проверил несколько раз, эффект стабильный. Уточняю: речь идёт именно про эту конкретную схему, и роутеры в режиме AP-bridge.

Прошу проверить эту ситуацию.

Логи:

R1:

Jan  1 06:00:04 syslogd started: BusyBox v1.31.1
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Determined physical RAM map:
Jan  1 06:00:04 kernel:  memory: 10000000 @ 00000000 (usable)
Jan  1 06:00:04 kernel: Detected 3 available secondary CPU(s)
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Zone PFN ranges:
Jan  1 06:00:04 kernel:   DMA      0x00000000 -> 0x00001000
Jan  1 06:00:04 kernel:   Normal   0x00001000 -> 0x00010000
Jan  1 06:00:04 kernel: Movable zone start PFN for each node
Jan  1 06:00:04 kernel: Early memory PFN ranges
Jan  1 06:00:04 kernel:     0: 0x00000000 -> 0x00010000
Jan  1 06:00:04 kernel: PERCPU: Embedded 7 pages/cpu @8162a000 s4512 r8192 d15968 u32768
Jan  1 06:00:04 kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Jan  1 06:00:04 kernel: Kernel command line: console=ttyS0,57600n8 root=/dev/mtdblock4 rootfstype=squashfs
Jan  1 06:00:04 kernel: PID hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 06:00:04 kernel: Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 06:00:04 kernel: Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 06:00:04 kernel: Writing ErrCtl register=0002a004
Jan  1 06:00:04 kernel: Readback ErrCtl register=0002a004
Jan  1 06:00:04 kernel: Memory: 255488k/262144k available (3248k kernel code, 6656k reserved, 692k data, 212k init, 0k highmem)
Jan  1 06:00:04 kernel: Hierarchical RCU implementation.
Jan  1 06:00:04 kernel: NR_IRQS:72
Jan  1 06:00:04 kernel: MIPS GIC RevID: 3.0
Jan  1 06:00:04 kernel: Setting up vectored interrupts
Jan  1 06:00:04 kernel: console [ttyS0] enabled
Jan  1 06:00:04 kernel: Calibrating delay loop... 577.53 BogoMIPS (lpj=288768)
Jan  1 06:00:04 kernel: pid_max: default: 32768 minimum: 301
Jan  1 06:00:04 kernel: Mount-cache hash table entries: 512
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Synchronize counters for CPU 1: done.
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 system: Start entropy increase daemon
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Synchronize counters for CPU 2: done.
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Synchronize counters for CPU 3: done.
Jan  1 06:00:04 kernel: Brought up 4 CPUs
Jan  1 06:00:04 kernel: NET: Registered protocol family 16
Jan  1 06:00:04 kernel: bio: create slab <bio-0> at 0
Jan  1 06:00:04 kernel: SCSI subsystem initialized
Jan  1 06:00:04 kernel: USB led has gpio 16
Jan  1 06:00:04 kernel: usbcore: registered new interface driver usbfs
Jan  1 06:00:04 kernel: usbcore: registered new interface driver hub
Jan  1 06:00:04 kernel: usbcore: registered new device driver usb
Jan  1 06:00:04 kernel: PCI host bridge to bus 0000:00
Jan  1 06:00:04 kernel: pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
Jan  1 06:00:04 kernel: pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
Jan  1 06:00:04 kernel: pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Jan  1 06:00:04 kernel: pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
Jan  1 06:00:04 kernel: pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
Jan  1 06:00:04 kernel: pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
Jan  1 06:00:04 kernel: pci 0000:00:00.0: PCI bridge to [bus 01-01]
Jan  1 06:00:04 kernel: pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
Jan  1 06:00:04 kernel: PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan  1 06:00:04 kernel: Switching to clocksource GIC
Jan  1 06:00:04 kernel: FS-Cache: Loaded
Jan  1 06:00:04 kernel: CacheFiles: Loaded
Jan  1 06:00:04 kernel: NET: Registered protocol family 1
Jan  1 06:00:04 kernel: NET: Registered protocol family 2
Jan  1 06:00:04 kernel: IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 06:00:04 kernel: TCP established hash table entries: 8192 (order: 4, 65536 bytes)
Jan  1 06:00:04 kernel: TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
Jan  1 06:00:04 kernel: TCP: Hash tables configured (established 8192 bind 8192)
Jan  1 06:00:04 kernel: TCP: reno registered
Jan  1 06:00:04 kernel: UDP hash table entries: 128 (order: 0, 4096 bytes)
Jan  1 06:00:04 kernel: 4 CPUs re-calibrate udelay (lpj = 289792)
Jan  1 06:00:04 kernel: Load Ralink WDG Timer Module
Jan  1 06:00:04 kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 06:00:04 kernel: msgmni has been set to 499
Jan  1 06:00:04 kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Jan  1 06:00:04 kernel: io scheduler noop registered (default)
Jan  1 06:00:04 kernel: Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Jan  1 06:00:04 kernel: serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A
Jan  1 06:00:04 kernel: USB power down at bootup use inverted gpio 14
Jan  1 06:00:04 kernel: Ralink gpio driver initialized
Jan  1 06:00:04 kernel: loop: module loaded
Jan  1 06:00:04 kernel: MediaTek SPI flash driver, SPI clock: 44MHz
Jan  1 06:00:04 kernel: SPI flash chip: W25Q128FV (ef 40180000) (16384 Kbytes)
Jan  1 06:00:04 kernel: Creating 8 MTD partitions on "raspi":
Jan  1 06:00:04 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Jan  1 06:00:04 kernel: 0x000000030000-0x000000040000 : "Config"
Jan  1 06:00:04 kernel: 0x000000040000-0x000000050000 : "Factory"
Jan  1 06:00:04 kernel: 0x000000050000-0x0000001ad729 : "Kernel_stub"
Jan  1 06:00:04 kernel: 0x0000001ad729-0x000000fc0000 : "RootFS_stub"
Jan  1 06:00:04 kernel: 0x000000f80000-0x000000fc0000 : "RW-FS"
Jan  1 06:00:04 kernel: 0x000000fc0000-0x000001000000 : "PS-FS"
Jan  1 06:00:04 kernel: 0x000000050000-0x000000fc0000 : "Kernel_RootFS"
Jan  1 06:00:04 kernel: Ralink APSoC Ethernet Driver v3.2.4 (raeth)
Jan  1 06:00:04 kernel: raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
Jan  1 06:00:04 kernel: raeth: NAPI & GRO support, weight 128
Jan  1 06:00:04 kernel: raeth: Byte Queue Limits (BQL) support
Jan  1 06:00:04 kernel: PPP generic driver version 2.4.2
Jan  1 06:00:04 kernel: PPP vpn led has gpio 13
Jan  1 06:00:04 kernel: PPP MPPE Compression module registered
Jan  1 06:00:04 kernel: NET: Registered protocol family 24
Jan  1 06:00:04 kernel: PPTP driver version 0.8.5
Jan  1 06:00:04 kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 06:00:04 kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan  1 06:00:04 kernel: U2PHY P0 set SRCTRL calibration value: 2
Jan  1 06:00:04 kernel: U2PHY P1 set SRCTRL calibration value: 2
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000
Jan  1 06:00:04 kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan  1 06:00:04 kernel: usb usb1: Product: xHCI Host Controller
Jan  1 06:00:04 kernel: usb usb1: Manufacturer: Linux 3.4.113.238 xhci-hcd
Jan  1 06:00:04 kernel: usb usb1: SerialNumber: xhci-hcd
Jan  1 06:00:04 kernel: hub 1-0:1.0: USB hub found
Jan  1 06:00:04 kernel: hub 1-0:1.0: 2 ports detected
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
Jan  1 06:00:04 kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
Jan  1 06:00:04 kernel: usb usb2: Product: xHCI Host Controller
Jan  1 06:00:04 kernel: usb usb2: Manufacturer: Linux 3.4.113.238 xhci-hcd
Jan  1 06:00:04 kernel: usb usb2: SerialNumber: xhci-hcd
Jan  1 06:00:04 kernel: hub 2-0:1.0: USB hub found
Jan  1 06:00:04 kernel: hub 2-0:1.0: 1 port detected
Jan  1 06:00:04 kernel: usbcore: registered new interface driver libusual
Jan  1 06:00:04 kernel: 8021q: 802.1Q VLAN Support v1.8
Jan  1 06:00:04 kernel: NET: Registered protocol family 17
Jan  1 06:00:04 kernel: Netfilter messages via NETLINK v0.30.
Jan  1 06:00:04 kernel: nf_conntrack version 0.5.0 (32768 buckets, 32768 max)
Jan  1 06:00:04 kernel: gre: GRE over IPv4 demultiplexor driver
Jan  1 06:00:04 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 06:00:04 kernel: TCP: cubic registered
Jan  1 06:00:04 kernel: NET: Registered protocol family 10
Jan  1 06:00:04 kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 06:00:04 kernel: L2TP core driver, V2.0
Jan  1 06:00:04 kernel: PPPoL2TP kernel driver, V2.0
Jan  1 06:00:04 kernel: L2TP netlink interface
Jan  1 06:00:04 kernel: Registering the dns_resolver key type
Jan  1 06:00:04 kernel: NVRAM: Kernel NVRAM start init.
Jan  1 06:00:04 kernel: NVRAM: Particion 0 CRC ccc82cde OK.
Jan  1 06:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Jan  1 06:00:04 kernel: mount /proc file system ok!
Jan  1 06:00:04 kernel: mount /proc/bus/usb file system ok!
Jan  1 06:00:04 kernel: mount /sys file system ok!
Jan  1 06:00:04 kernel: mount /dev file system ok!
Jan  1 06:00:04 kernel: mount /var file system ok!
Jan  1 06:00:04 kernel: Freeing unused kernel memory: 212k freed
Jan  1 06:00:04 kernel: Build the /dev/console node.
Jan  1 06:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan  1 06:00:04 haveged: haveged starting up
Jan  1 06:00:04 system: Sart update service
Jan  1 06:00:04 sysctl: Tune kernel with sysctl.
Jan  1 06:00:04 pass: Set current password
Jan  1 06:00:04 pass: WARNING!!! You use default Login and Password!!! Please change it.
Jan  1 06:00:04 syslog: password for 'Admin' changed
Aug 11 12:31:00 ntp: Starting NTPD.
Aug 11 12:31:00 hotplug: Generate config file.
Aug 11 12:31:00 hotplug: Starting MDEV helper as daemon.
Aug 11 12:31:00 hotplug: Refresh dev nodes.
Aug 11 12:31:00 hotplug: Rescan connected devices
Aug 11 12:31:00 usbctrl(272): TYPE=9/0/1 INTERFACE=9/0/0
Aug 11 12:31:00 usbctrl(277): TYPE=9/0/3 INTERFACE=9/0/0
Aug 11 12:31:00 modules: Starting modules.dep generate.
Aug 11 12:31:02 modules: Load conntrack helpers modules.
Aug 11 12:31:02 modules: Load application depended modules.
Aug 11 12:31:02 lo: Starting loopback interface.
Aug 11 12:31:02 lan: Starting LAN network interfaces.
Aug 11 12:31:02 NETPRECONF: eth2 MACADDR A0:22:4E:C3:FA:66 txqueuelen 200
Aug 11 12:31:02 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Aug 11 12:31:02 kernel: raeth: HW VLAN TX offload enabled
Aug 11 12:31:02 kernel: raeth: HW Scatter/Gather TX offload enabled
Aug 11 12:31:02 NETPRECONF: eth3 MACADDR A0:22:4E:C2:B0:9F txqueuelen 200
Aug 11 12:31:02 lan: Add bridge in the system
Aug 11 12:31:02 lan: br0_MACADDR A0:22:4E:C3:FA:66
Aug 11 12:31:02 lan: Up bridge interface
Aug 11 12:31:02 lan: Add LAN Mode is 0 lan iface br0, adress 169.254.92.17
Aug 11 12:31:03 global: Generate resolv at local.
Aug 11 12:31:03 global: Install ipv4 DNS servers to local resolv.
Aug 11 12:31:03 dnsserver: Generate /etc/hosts file.
Aug 11 12:31:03 dnsserver: Starting DNSMASQ.
Aug 11 12:31:03 inetd: Starting inetd.
Aug 11 12:31:03 dnsmasq[648]: started, version 2.81 cachesize 4096
Aug 11 12:31:03 dnsmasq[648]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-UBus no-i18n no-IDN no-DHCP no-scripts no-TFTP no-conntrack no-ipset no-auth DNSSEC loop-detect inotify no-dumpfile
Aug 11 12:31:03 dnsmasq[648]: read /etc/hosts - 5 addresses
Aug 11 12:31:05 global: Switch to 2nd boot stage.
Aug 11 12:31:05 global: Flush route and conntrack cache
Aug 11 12:31:05 services: stop needed services and scripts (all).
Aug 11 12:31:05 QoS: Stopping SHAPER.
Aug 11 12:31:06 ntp: Stopping NTPD.
Aug 11 12:31:07 inetd: Stopping inetd.
Aug 11 12:31:08 vpnhelper: Flush route and conntrack cache  169.254.92.17
Aug 11 12:31:09 kernel: do_page_fault(): sending SIGSEGV to sh for invalid read access from 00000018
Aug 11 12:31:09 kernel: epc = 00000019 in busybox[400000+b3000]
Aug 11 12:31:09 kernel: ra  = 77f88868 in libuClibc-1.0.34.so[77f29000+97000]
Aug 11 12:31:09 reconfig: Flush route and conntrack cache  169.254.92.17
Aug 11 12:31:09 modules: Load conntrack helpers modules.
Aug 11 12:31:09 modules: Load application depended modules.
Aug 11 12:31:09 modules: Prepare wifi config.
Aug 11 12:31:09 modules: Load wireless modules.
Aug 11 12:31:09 modules: Load wifi AP module.
Aug 11 12:31:09 kernel: PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Aug 11 12:31:09 kernel: MT7615 AP Driver version: 5.0.4.0.P90
Aug 11 12:31:09 lan: Stopping LAN network interfaces.
Aug 11 12:31:09 lan: Starting LAN network interfaces.
Aug 11 12:31:10 lan: Add bridge in the system
Aug 11 12:31:10 lan: br0_MACADDR A0:22:4E:C3:FA:66
Aug 11 12:31:10 lan: Up bridge interface
Aug 11 12:31:10 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Aug 11 12:31:10 kernel: raeth: HW VLAN TX offload enabled
Aug 11 12:31:10 kernel: raeth: HW Scatter/Gather TX offload enabled
Aug 11 12:31:10 lan: Add LAN Mode is 0 lan iface br0, adress 169.254.177.218
Aug 11 12:31:10 reconfig: Bridge OperationMode: 0
Aug 11 12:31:10 reconfig: Add interface eth2 to br0 bridge
Aug 11 12:31:10 kernel: device eth2 entered promiscuous mode
Aug 11 12:31:10 kernel: br0: port 1(eth2) entered forwarding state
Aug 11 12:31:11 kernel: br0: port 1(eth2) entered forwarding state
Aug 11 12:31:21 reconfig: Add interface ra0 to br0 bridge
Aug 11 12:31:21 kernel: device ra0 entered promiscuous mode
Aug 11 12:31:21 kernel: br0: port 2(ra0) entered forwarding state
Aug 11 12:31:22 kernel: br0: port 2(ra0) entered forwarding state
Aug 11 12:31:23 reconfig: Add interface rai0 to br0 bridge
Aug 11 12:31:23 kernel: device rai0 entered promiscuous mode
Aug 11 12:31:23 kernel: br0: port 3(rai0) entered forwarding state
Aug 11 12:31:23 reconfig: Add interface wdsi0 to br0 bridge
Aug 11 12:31:23 reconfig: WiFi ra0 interface set txqueuelen 50.
Aug 11 12:31:23 reconfig: WiFi rai0 interface set txqueuelen 50.
Aug 11 12:31:23 wan: Starting WAN config.
Aug 11 12:31:23 wan: Starting DHCP client at br0.
Aug 11 12:31:23 udhcpc[1821]: started, v1.31.1
Aug 11 12:31:23 udhcpc: AP All deconfig br0.
Aug 11 12:31:24 ESW: Reset LAN ports phys
Aug 11 12:31:24 kernel: br0: port 3(rai0) entered forwarding state
Aug 11 12:31:25 advanced: Tune wifi advanced parametrs for ra0.
Aug 11 12:31:25 advanced: Tune wifi advanced parametrs for rai0.
Aug 11 12:31:25 services: start needed services and scripts (all).
Aug 11 12:31:25 udhcpc: AP DHCP adress get fail use default 192.168.2.1
Aug 11 12:31:25 udhcpc: AP Add route to multicast subnet.
Aug 11 12:31:25 udhcpc: AP Restart needed services
Aug 11 12:31:26 QoS: Set default rules.
Aug 11 12:31:26 Codel: QoS Add codel for all interfaces.
Aug 11 12:31:26 iptables: Add netfiler rules
Aug 11 12:31:26 iptables: Allow established/related in input
Aug 11 12:31:26 iptables: Drop invalid state connections
Aug 11 12:31:26 iptables: Service limit set
Aug 11 12:31:26 iptables: Set igmp input rules
Aug 11 12:31:26 iptables: DHCP server allow
Aug 11 12:31:26 iptables: Dnsproxy allow to connect
Aug 11 12:31:26 iptables: Remote managment web limit
Aug 11 12:31:26 iptables: Remote managment ssh limit
Aug 11 12:31:26 iptables: Remote managment telnet limit
Aug 11 12:31:26 iptables: Allow rate limited ping from all interfaces.
Aug 11 12:31:26 iptables: Allow established/related in forward
Aug 11 12:31:26 global: Install ipv4 DNS servers to local resolv.
Aug 11 12:31:27 dnsserver: Generate /etc/hosts file.
Aug 11 12:31:27 dnsserver: Send HUP to dnsmasq.
Aug 11 12:31:27 dnsmasq[648]: read /etc/hosts - 5 addresses
Aug 11 12:31:27 ntp: Starting NTPD.
Aug 11 12:31:27 kext: Nat mode Linux Hybrid
Aug 11 12:31:27 kext: NAT Offload mode not supported in this device mode (bridge/apclibridge/etc), hw_nat and all fastpaths disabled.
Aug 11 12:31:27 kext: Enable multicast to unicast conversion for ra0 rai0
Aug 11 12:31:28 lld2d: Starting LLD2D.
Aug 11 12:31:28 inetd: Starting inetd.
Aug 11 12:31:28 dhcpd: DHCP server disabled. OPMODE=0 APCLIBR=0
Aug 11 12:31:29 irqbalance: Starting irqbalance routing/wifi optimize mode.
Aug 11 12:31:29 irqbalance: Starting irqbalance auto mode.
Aug 11 12:31:30 services: restart needed services and scripts (dhcp).
Aug 11 12:31:30 QoS: Stopping SHAPER.
Aug 11 12:31:30 QoS: Set default rules.
Aug 11 12:31:30 Codel: QoS Add codel for all interfaces.
Aug 11 12:31:30 global: USB Port power ON.
Aug 11 12:31:30 hotplug: Rescan connected devices
Aug 11 12:31:30 global: Copy web pages to tmpfs.
Aug 11 12:31:30 iptables: Add netfiler rules
Aug 11 12:31:30 iptables: Allow established/related in input
Aug 11 12:31:30 iptables: Drop invalid state connections
Aug 11 12:31:30 iptables: Service limit set
Aug 11 12:31:30 iptables: Set igmp input rules
Aug 11 12:31:30 iptables: DHCP server allow
Aug 11 12:31:30 iptables: Dnsproxy allow to connect
Aug 11 12:31:30 iptables: Remote managment web limit
Aug 11 12:31:30 iptables: Remote managment ssh limit
Aug 11 12:31:30 usbctrl(3348): TYPE=9/0/1 INTERFACE=9/0/0
Aug 11 12:31:30 iptables: Remote managment telnet limit
Aug 11 12:31:30 iptables: Allow rate limited ping from all interfaces.
Aug 11 12:31:30 usbctrl(3359): TYPE=9/0/3 INTERFACE=9/0/0
Aug 11 12:31:30 iptables: Allow established/related in forward
Aug 11 12:31:31 global: Install ipv4 DNS servers to local resolv.
Aug 11 12:31:31 global: Starting WEB Managment Server.
Aug 11 12:31:31 dnsserver: Generate /etc/hosts file.
Aug 11 12:31:31 dnsserver: Send HUP to dnsmasq.
Aug 11 12:31:31 dnsmasq[648]: read /etc/hosts - 5 addresses
Aug 11 12:31:31 ntp: Stopping NTPD.
Aug 11 12:31:32 ntp: Starting NTPD.
Aug 11 12:31:33 irqbalance: Stopping irqbalance.
Aug 11 12:31:33 irqbalance: Starting irqbalance routing/wifi optimize mode.
Aug 11 12:31:34 irqbalance: Starting irqbalance auto mode.
Aug 11 12:31:34 udhcpc: AP End fallback procedure.
Aug 11 12:31:34 udhcpc[1821]: sending discover
Aug 11 12:31:38 udhcpc[1821]: sending discover
Aug 11 12:31:44 udhcpc[1821]: sending discover
Aug 11 12:31:47 nginx: 2020/08/11 12:31:47 [info] 3554#0: *1 Authentication successful: user=Admin , client: 192.168.2.10, server: localhost, request: "POST /goform/auth HTTP/1.1", host: "192.168.2.1", referrer: "http://192.168.2.1/login.asp"
Aug 11 12:31:49 udhcpc[1821]: sending discover
Aug 11 12:31:53 udhcpc[1821]: sending discover
Aug 11 12:31:59 udhcpc: AP Lease fail br0.
Aug 11 12:32:18 udhcpc[1821]: sending discover
Aug 11 12:32:23 udhcpc[1821]: sending discover
Aug 11 12:32:29 udhcpc[1821]: sending discover
Aug 11 12:32:34 udhcpc[1821]: sending discover
Aug 11 12:32:38 udhcpc[1821]: sending discover
Aug 11 12:32:43 udhcpc: AP Lease fail br0.
Aug 11 12:33:03 udhcpc[1821]: sending discover

 

R2:

Jan  1 06:00:04 syslogd started: BusyBox v1.31.1
Jan  1 06:00:04 kernel: CPU/OCP/SYS frequency: 880/293/220 MHz
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Determined physical RAM map:
Jan  1 06:00:04 kernel:  memory: 10000000 @ 00000000 (usable)
Jan  1 06:00:04 kernel: Detected 3 available secondary CPU(s)
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Zone PFN ranges:
Jan  1 06:00:04 kernel:   DMA      0x00000000 -> 0x00001000
Jan  1 06:00:04 kernel:   Normal   0x00001000 -> 0x00010000
Jan  1 06:00:04 kernel: Movable zone start PFN for each node
Jan  1 06:00:04 kernel: Early memory PFN ranges
Jan  1 06:00:04 kernel:     0: 0x00000000 -> 0x00010000
Jan  1 06:00:04 kernel: PERCPU: Embedded 7 pages/cpu @8162a000 s4512 r8192 d15968 u32768
Jan  1 06:00:04 kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Jan  1 06:00:04 kernel: Kernel command line: console=ttyS0,57600n8 root=/dev/mtdblock4 rootfstype=squashfs
Jan  1 06:00:04 kernel: PID hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 06:00:04 kernel: Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 06:00:04 kernel: Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 06:00:04 kernel: Writing ErrCtl register=00040002
Jan  1 06:00:04 kernel: Readback ErrCtl register=00040002
Jan  1 06:00:04 kernel: Memory: 255488k/262144k available (3248k kernel code, 6656k reserved, 692k data, 212k init, 0k highmem)
Jan  1 06:00:04 kernel: Hierarchical RCU implementation.
Jan  1 06:00:04 kernel: NR_IRQS:72
Jan  1 06:00:04 kernel: MIPS GIC RevID: 3.0
Jan  1 06:00:04 kernel: Setting up vectored interrupts
Jan  1 06:00:04 kernel: console [ttyS0] enabled
Jan  1 06:00:04 kernel: Calibrating delay loop... 577.53 BogoMIPS (lpj=288768)
Jan  1 06:00:04 kernel: pid_max: default: 32768 minimum: 301
Jan  1 06:00:04 kernel: Mount-cache hash table entries: 512
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Synchronize counters for CPU 1: done.
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 system: Start entropy increase daemon
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Synchronize counters for CPU 2: done.
Jan  1 06:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan  1 06:00:04 kernel: MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Jan  1 06:00:04 kernel: CPU revision is: 0001992f (MIPS 1004Kc)
Jan  1 06:00:04 kernel: Synchronize counters for CPU 3: done.
Jan  1 06:00:04 kernel: Brought up 4 CPUs
Jan  1 06:00:04 kernel: NET: Registered protocol family 16
Jan  1 06:00:04 kernel: bio: create slab <bio-0> at 0
Jan  1 06:00:04 kernel: SCSI subsystem initialized
Jan  1 06:00:04 kernel: USB led has gpio 16
Jan  1 06:00:04 kernel: usbcore: registered new interface driver usbfs
Jan  1 06:00:04 kernel: usbcore: registered new interface driver hub
Jan  1 06:00:04 kernel: usbcore: registered new device driver usb
Jan  1 06:00:04 kernel: PCI host bridge to bus 0000:00
Jan  1 06:00:04 kernel: pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
Jan  1 06:00:04 kernel: pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
Jan  1 06:00:04 kernel: pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Jan  1 06:00:04 kernel: pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
Jan  1 06:00:04 kernel: pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
Jan  1 06:00:04 kernel: pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
Jan  1 06:00:04 kernel: pci 0000:00:00.0: PCI bridge to [bus 01-01]
Jan  1 06:00:04 kernel: pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
Jan  1 06:00:04 kernel: PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan  1 06:00:04 kernel: Switching to clocksource GIC
Jan  1 06:00:04 kernel: FS-Cache: Loaded
Jan  1 06:00:04 kernel: CacheFiles: Loaded
Jan  1 06:00:04 kernel: NET: Registered protocol family 1
Jan  1 06:00:04 kernel: NET: Registered protocol family 2
Jan  1 06:00:04 kernel: IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 06:00:04 kernel: TCP established hash table entries: 8192 (order: 4, 65536 bytes)
Jan  1 06:00:04 kernel: TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
Jan  1 06:00:04 kernel: TCP: Hash tables configured (established 8192 bind 8192)
Jan  1 06:00:04 kernel: TCP: reno registered
Jan  1 06:00:04 kernel: UDP hash table entries: 128 (order: 0, 4096 bytes)
Jan  1 06:00:04 kernel: 4 CPUs re-calibrate udelay (lpj = 289792)
Jan  1 06:00:04 kernel: Load Ralink WDG Timer Module
Jan  1 06:00:04 kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 06:00:04 kernel: msgmni has been set to 499
Jan  1 06:00:04 kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Jan  1 06:00:04 kernel: io scheduler noop registered (default)
Jan  1 06:00:04 kernel: Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Jan  1 06:00:04 kernel: serial8250: ttyS0 at MMIO 0x1e000c00 (irq = 34) is a 16550A
Jan  1 06:00:04 kernel: USB power down at bootup use inverted gpio 14
Jan  1 06:00:04 kernel: Ralink gpio driver initialized
Jan  1 06:00:04 kernel: loop: module loaded
Jan  1 06:00:04 kernel: MediaTek SPI flash driver, SPI clock: 44MHz
Jan  1 06:00:04 kernel: SPI flash chip: W25Q128FV (ef 40180000) (16384 Kbytes)
Jan  1 06:00:04 kernel: Creating 8 MTD partitions on "raspi":
Jan  1 06:00:04 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Jan  1 06:00:04 kernel: 0x000000030000-0x000000040000 : "Config"
Jan  1 06:00:04 kernel: 0x000000040000-0x000000050000 : "Factory"
Jan  1 06:00:04 kernel: 0x000000050000-0x0000001ad729 : "Kernel_stub"
Jan  1 06:00:04 kernel: 0x0000001ad729-0x000000fc0000 : "RootFS_stub"
Jan  1 06:00:04 kernel: 0x000000f80000-0x000000fc0000 : "RW-FS"
Jan  1 06:00:04 kernel: 0x000000fc0000-0x000001000000 : "PS-FS"
Jan  1 06:00:04 kernel: 0x000000050000-0x000000fc0000 : "Kernel_RootFS"
Jan  1 06:00:04 kernel: Ralink APSoC Ethernet Driver v3.2.4 (raeth)
Jan  1 06:00:04 kernel: raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
Jan  1 06:00:04 kernel: raeth: NAPI & GRO support, weight 128
Jan  1 06:00:04 kernel: raeth: Byte Queue Limits (BQL) support
Jan  1 06:00:04 kernel: PPP generic driver version 2.4.2
Jan  1 06:00:04 kernel: PPP vpn led has gpio 13
Jan  1 06:00:04 kernel: PPP MPPE Compression module registered
Jan  1 06:00:04 kernel: NET: Registered protocol family 24
Jan  1 06:00:04 kernel: PPTP driver version 0.8.5
Jan  1 06:00:04 kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 06:00:04 kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan  1 06:00:04 kernel: U2PHY P0 set SRCTRL calibration value: 2
Jan  1 06:00:04 kernel: U2PHY P1 set SRCTRL calibration value: 2
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000
Jan  1 06:00:04 kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan  1 06:00:04 kernel: usb usb1: Product: xHCI Host Controller
Jan  1 06:00:04 kernel: usb usb1: Manufacturer: Linux 3.4.113.238 xhci-hcd
Jan  1 06:00:04 kernel: usb usb1: SerialNumber: xhci-hcd
Jan  1 06:00:04 kernel: hub 1-0:1.0: USB hub found
Jan  1 06:00:04 kernel: hub 1-0:1.0: 2 ports detected
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: xHCI Host Controller
Jan  1 06:00:04 kernel: xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
Jan  1 06:00:04 kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
Jan  1 06:00:04 kernel: usb usb2: Product: xHCI Host Controller
Jan  1 06:00:04 kernel: usb usb2: Manufacturer: Linux 3.4.113.238 xhci-hcd
Jan  1 06:00:04 kernel: usb usb2: SerialNumber: xhci-hcd
Jan  1 06:00:04 kernel: hub 2-0:1.0: USB hub found
Jan  1 06:00:04 kernel: hub 2-0:1.0: 1 port detected
Jan  1 06:00:04 kernel: usbcore: registered new interface driver libusual
Jan  1 06:00:04 kernel: 8021q: 802.1Q VLAN Support v1.8
Jan  1 06:00:04 kernel: NET: Registered protocol family 17
Jan  1 06:00:04 kernel: Netfilter messages via NETLINK v0.30.
Jan  1 06:00:04 kernel: nf_conntrack version 0.5.0 (32768 buckets, 32768 max)
Jan  1 06:00:04 kernel: gre: GRE over IPv4 demultiplexor driver
Jan  1 06:00:04 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 06:00:04 kernel: TCP: cubic registered
Jan  1 06:00:04 kernel: NET: Registered protocol family 10
Jan  1 06:00:04 kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 06:00:04 kernel: L2TP core driver, V2.0
Jan  1 06:00:04 kernel: PPPoL2TP kernel driver, V2.0
Jan  1 06:00:04 kernel: L2TP netlink interface
Jan  1 06:00:04 kernel: Registering the dns_resolver key type
Jan  1 06:00:04 kernel: NVRAM: Kernel NVRAM start init.
Jan  1 06:00:04 kernel: NVRAM: Particion 0 CRC acb19651 OK.
Jan  1 06:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Jan  1 06:00:04 kernel: mount /proc file system ok!
Jan  1 06:00:04 kernel: mount /proc/bus/usb file system ok!
Jan  1 06:00:04 kernel: mount /sys file system ok!
Jan  1 06:00:04 kernel: mount /dev file system ok!
Jan  1 06:00:04 kernel: mount /var file system ok!
Jan  1 06:00:04 kernel: Freeing unused kernel memory: 212k freed
Jan  1 06:00:04 kernel: Build the /dev/console node.
Jan  1 06:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan  1 06:00:04 haveged: haveged starting up
Jan  1 06:00:04 system: Sart update service
Jan  1 06:00:04 sysctl: Tune kernel with sysctl.
Jan  1 06:00:04 pass: Set current password
Jan  1 06:00:04 pass: WARNING!!! You use default Login and Password!!! Please change it.
Jan  1 06:00:04 syslog: password for 'Admin' changed
Aug 11 12:31:00 ntp: Starting NTPD.
Aug 11 12:31:00 hotplug: Generate config file.
Aug 11 12:31:00 hotplug: Starting MDEV helper as daemon.
Aug 11 12:31:00 hotplug: Refresh dev nodes.
Aug 11 12:31:00 hotplug: Rescan connected devices
Aug 11 12:31:00 usbctrl(276): TYPE=9/0/1 INTERFACE=9/0/0
Aug 11 12:31:00 modules: Starting modules.dep generate.
Aug 11 12:31:00 usbctrl(301): TYPE=9/0/3 INTERFACE=9/0/0
Aug 11 12:31:02 modules: Load conntrack helpers modules.
Aug 11 12:31:02 modules: Load application depended modules.
Aug 11 12:31:02 lo: Starting loopback interface.
Aug 11 12:31:02 lan: Starting LAN network interfaces.
Aug 11 12:31:02 NETPRECONF: eth2 MACADDR A0:22:4E:CE:B6:24 txqueuelen 200
Aug 11 12:31:02 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Aug 11 12:31:02 kernel: raeth: HW VLAN TX offload enabled
Aug 11 12:31:02 kernel: raeth: HW Scatter/Gather TX offload enabled
Aug 11 12:31:02 NETPRECONF: eth3 MACADDR A0:22:4E:C0:A9:1C txqueuelen 200
Aug 11 12:31:02 lan: Add bridge in the system
Aug 11 12:31:02 lan: br0_MACADDR A0:22:4E:CE:B6:24
Aug 11 12:31:02 lan: Up bridge interface
Aug 11 12:31:02 lan: Add LAN Mode is 0 lan iface br0, adress 169.254.146.170
Aug 11 12:31:02 global: Generate resolv at local.
Aug 11 12:31:02 global: Install ipv4 DNS servers to local resolv.
Aug 11 12:31:03 dnsserver: Generate /etc/hosts file.
Aug 11 12:31:03 dnsserver: Starting DNSMASQ.
Aug 11 12:31:03 inetd: Starting inetd.
Aug 11 12:31:03 dnsmasq[649]: started, version 2.81 cachesize 4096
Aug 11 12:31:03 dnsmasq[649]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-UBus no-i18n no-IDN no-DHCP no-scripts no-TFTP no-conntrack no-ipset no-auth DNSSEC loop-detect inotify no-dumpfile
Aug 11 12:31:03 dnsmasq[649]: read /etc/hosts - 5 addresses
Aug 11 12:31:05 global: Switch to 2nd boot stage.
Aug 11 12:31:05 global: Flush route and conntrack cache
Aug 11 12:31:05 services: stop needed services and scripts (all).
Aug 11 12:31:05 QoS: Stopping SHAPER.
Aug 11 12:31:06 ntp: Stopping NTPD.
Aug 11 12:31:07 inetd: Stopping inetd.
Aug 11 12:31:08 vpnhelper: Flush route and conntrack cache  169.254.146.170
Aug 11 12:31:09 reconfig: Flush route and conntrack cache  169.254.146.170
Aug 11 12:31:09 modules: Load conntrack helpers modules.
Aug 11 12:31:09 modules: Load application depended modules.
Aug 11 12:31:09 modules: Prepare wifi config.
Aug 11 12:31:09 modules: Load wireless modules.
Aug 11 12:31:09 modules: Load wifi AP module.
Aug 11 12:31:09 kernel: PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Aug 11 12:31:09 kernel: MT7615 AP Driver version: 5.0.4.0.P90
Aug 11 12:31:09 lan: Stopping LAN network interfaces.
Aug 11 12:31:09 lan: Starting LAN network interfaces.
Aug 11 12:31:10 lan: Add bridge in the system
Aug 11 12:31:10 lan: br0_MACADDR A0:22:4E:CE:B6:24
Aug 11 12:31:10 lan: Up bridge interface
Aug 11 12:31:10 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Aug 11 12:31:10 kernel: raeth: HW VLAN TX offload enabled
Aug 11 12:31:10 kernel: raeth: HW Scatter/Gather TX offload enabled
Aug 11 12:31:10 lan: Add LAN Mode is 0 lan iface br0, adress 169.254.22.123
Aug 11 12:31:10 reconfig: Bridge OperationMode: 0
Aug 11 12:31:10 reconfig: Add interface eth2 to br0 bridge
Aug 11 12:31:10 kernel: device eth2 entered promiscuous mode
Aug 11 12:31:10 kernel: br0: port 1(eth2) entered forwarding state
Aug 11 12:31:11 kernel: br0: port 1(eth2) entered forwarding state
Aug 11 12:31:21 reconfig: Add interface ra0 to br0 bridge
Aug 11 12:31:21 kernel: device ra0 entered promiscuous mode
Aug 11 12:31:21 kernel: br0: port 2(ra0) entered forwarding state
Aug 11 12:31:22 kernel: br0: port 2(ra0) entered forwarding state
Aug 11 12:31:23 reconfig: Add interface rai0 to br0 bridge
Aug 11 12:31:23 kernel: device rai0 entered promiscuous mode
Aug 11 12:31:23 kernel: br0: port 3(rai0) entered forwarding state
Aug 11 12:31:23 reconfig: Add interface wdsi0 to br0 bridge
Aug 11 12:31:23 reconfig: WiFi ra0 interface set txqueuelen 50.
Aug 11 12:31:23 reconfig: WiFi rai0 interface set txqueuelen 50.
Aug 11 12:31:23 wan: Starting WAN config.
Aug 11 12:31:23 wan: Starting DHCP client at br0.
Aug 11 12:31:23 udhcpc[1849]: started, v1.31.1
Aug 11 12:31:23 udhcpc: AP All deconfig br0.
Aug 11 12:31:24 ESW: Reset LAN ports phys
Aug 11 12:31:24 kernel: br0: port 3(rai0) entered forwarding state
Aug 11 12:31:25 advanced: Tune wifi advanced parametrs for ra0.
Aug 11 12:31:25 advanced: Tune wifi advanced parametrs for rai0.
Aug 11 12:31:25 services: start needed services and scripts (all).
Aug 11 12:31:25 udhcpc: AP DHCP adress get fail use default 192.168.2.2
Aug 11 12:31:25 udhcpc: AP Add route to multicast subnet.
Aug 11 12:31:25 udhcpc: AP Restart needed services
Aug 11 12:31:26 QoS: Set default rules.
Aug 11 12:31:26 Codel: QoS Add codel for all interfaces.
Aug 11 12:31:26 iptables: Add netfiler rules
Aug 11 12:31:26 iptables: Allow established/related in input
Aug 11 12:31:26 iptables: Drop invalid state connections
Aug 11 12:31:26 iptables: Service limit set
Aug 11 12:31:26 iptables: Set igmp input rules
Aug 11 12:31:26 iptables: DHCP server allow
Aug 11 12:31:26 iptables: Dnsproxy allow to connect
Aug 11 12:31:26 iptables: Remote managment web limit
Aug 11 12:31:26 iptables: Remote managment ssh limit
Aug 11 12:31:26 iptables: Remote managment telnet limit
Aug 11 12:31:26 iptables: Allow rate limited ping from all interfaces.
Aug 11 12:31:26 iptables: Allow established/related in forward
Aug 11 12:31:26 global: Install ipv4 DNS servers to local resolv.
Aug 11 12:31:27 dnsserver: Generate /etc/hosts file.
Aug 11 12:31:27 dnsserver: Send HUP to dnsmasq.
Aug 11 12:31:27 dnsmasq[649]: read /etc/hosts - 5 addresses
Aug 11 12:31:27 ntp: Starting NTPD.
Aug 11 12:31:27 kext: Nat mode Linux Hybrid
Aug 11 12:31:27 kext: NAT Offload mode not supported in this device mode (bridge/apclibridge/etc), hw_nat and all fastpaths disabled.
Aug 11 12:31:27 kext: Enable multicast to unicast conversion for ra0 rai0
Aug 11 12:31:28 lld2d: Starting LLD2D.
Aug 11 12:31:28 inetd: Starting inetd.
Aug 11 12:31:28 dhcpd: DHCP server disabled. OPMODE=0 APCLIBR=0
Aug 11 12:31:29 irqbalance: Starting irqbalance routing/wifi optimize mode.
Aug 11 12:31:29 irqbalance: Starting irqbalance auto mode.
Aug 11 12:31:30 services: restart needed services and scripts (dhcp).
Aug 11 12:31:30 QoS: Stopping SHAPER.
Aug 11 12:31:30 QoS: Set default rules.
Aug 11 12:31:30 Codel: QoS Add codel for all interfaces.
Aug 11 12:31:30 global: USB Port power ON.
Aug 11 12:31:30 hotplug: Rescan connected devices
Aug 11 12:31:30 global: Copy web pages to tmpfs.
Aug 11 12:31:30 iptables: Add netfiler rules
Aug 11 12:31:30 iptables: Allow established/related in input
Aug 11 12:31:30 iptables: Drop invalid state connections
Aug 11 12:31:30 iptables: Service limit set
Aug 11 12:31:30 iptables: Set igmp input rules
Aug 11 12:31:30 iptables: DHCP server allow
Aug 11 12:31:30 iptables: Dnsproxy allow to connect
Aug 11 12:31:30 iptables: Remote managment web limit
Aug 11 12:31:30 iptables: Remote managment ssh limit
Aug 11 12:31:30 iptables: Remote managment telnet limit
Aug 11 12:31:30 iptables: Allow rate limited ping from all interfaces.
Aug 11 12:31:30 usbctrl(3360): TYPE=9/0/1 INTERFACE=9/0/0
Aug 11 12:31:30 iptables: Allow established/related in forward
Aug 11 12:31:30 usbctrl(3371): TYPE=9/0/3 INTERFACE=9/0/0
Aug 11 12:31:31 global: Install ipv4 DNS servers to local resolv.
Aug 11 12:31:31 global: Starting WEB Managment Server.
Aug 11 12:31:31 dnsserver: Generate /etc/hosts file.
Aug 11 12:31:31 dnsserver: Send HUP to dnsmasq.
Aug 11 12:31:31 dnsmasq[649]: read /etc/hosts - 5 addresses
Aug 11 12:31:31 ntp: Stopping NTPD.
Aug 11 12:31:32 ntp: Starting NTPD.
Aug 11 12:31:33 irqbalance: Stopping irqbalance.
Aug 11 12:31:34 irqbalance: Starting irqbalance routing/wifi optimize mode.
Aug 11 12:31:34 irqbalance: Starting irqbalance auto mode.
Aug 11 12:31:34 udhcpc: AP End fallback procedure.
Aug 11 12:31:34 udhcpc[1849]: sending discover
Aug 11 12:31:40 udhcpc[1849]: sending discover
Aug 11 12:31:44 udhcpc[1849]: sending discover
Aug 11 12:31:49 udhcpc[1849]: sending discover
Aug 11 12:31:50 nginx: 2020/08/11 12:31:50 [info] 3561#0: *1 Authentication successful: user=Admin , client: 192.168.2.10, server: localhost, request: "POST /goform/auth HTTP/1.1", host: "192.168.2.2", referrer: "http://192.168.2.2/login.asp"
Aug 11 12:31:54 udhcpc[1849]: sending discover
Aug 11 12:31:59 udhcpc: AP Lease fail br0.
Aug 11 12:32:19 udhcpc[1849]: sending discover
Aug 11 12:32:25 udhcpc[1849]: sending discover
Aug 11 12:32:30 udhcpc[1849]: sending discover
Aug 11 12:32:35 udhcpc[1849]: sending discover
Aug 11 12:32:39 udhcpc[1849]: sending discover
Aug 11 12:32:45 udhcpc: AP Lease fail br0.
Aug 11 12:33:05 udhcpc[1849]: sending discover
Aug 11 12:33:10 udhcpc[1849]: sending discover
Aug 11 12:33:15 udhcpc[1849]: sending discover
Aug 11 12:33:20 udhcpc[1849]: sending discover
Aug 11 12:33:24 udhcpc[1849]: sending discover
Aug 11 12:33:30 udhcpc: AP Lease fail br0.
Aug 11 12:33:50 udhcpc[1849]: sending discover
Aug 11 12:33:54 udhcpc[1849]: sending discover
Aug 11 12:33:59 udhcpc[1849]: sending discover
Aug 11 12:34:04 udhcpc[1849]: sending discover
Aug 11 12:34:09 udhcpc[1849]: sending discover
Aug 11 12:34:15 udhcpc: AP Lease fail br0.
Aug 11 12:34:35 udhcpc[1849]: sending discover
Aug 11 12:34:40 udhcpc[1849]: sending discover
Aug 11 12:34:45 udhcpc[1849]: sending discover
Aug 11 12:34:50 udhcpc[1849]: sending discover
Aug 11 12:34:55 udhcpc[1849]: sending discover
Aug 11 12:35:00 udhcpc: AP Lease fail br0.
Aug 11 12:35:19 udhcpc[1849]: sending discover
Aug 11 12:35:24 udhcpc[1849]: sending discover
Aug 11 12:35:29 udhcpc[1849]: sending discover
Aug 11 12:35:34 udhcpc[1849]: sending discover
Aug 11 12:35:39 udhcpc[1849]: sending discover
Aug 11 12:35:45 udhcpc: AP Lease fail br0.
Aug 11 12:36:05 udhcpc[1849]: sending discover
Aug 11 12:36:10 udhcpc[1849]: sending discover
Aug 11 12:36:15 udhcpc[1849]: sending discover
Aug 11 12:36:20 udhcpc[1849]: sending discover
Aug 11 12:36:25 udhcpc[1849]: sending discover
Aug 11 12:36:30 udhcpc: AP Lease fail br0.
Aug 11 12:36:49 udhcpc[1849]: sending discover
Aug 11 12:36:55 udhcpc[1849]: sending discover
Aug 11 12:37:00 udhcpc[1849]: sending discover
Aug 11 12:37:05 udhcpc[1849]: sending discover
Aug 11 12:37:10 udhcpc[1849]: sending discover
Aug 11 12:37:15 udhcpc: AP Lease fail br0.

 

 

 

Загруженные файлы:
  • Вам нужно войти, чтобы просматривать прикрепленные файлы..
Последний раз редактировалось 13/08/2020, 22:22 : termit
termit
termit@termit
52 СообщенияАвтор темы
#2 · 13/08/2020, 22:12

Петли, которая могла бы мешать пинговать роутеры, и положить сетёшку, не было. Да тогда и ноуты между собой бы не пинговались, и это не лечилось бы перезагрузкой роутеров. Кроме того, я отключал кабель между роутерами для проверки.

sfstudio
sfstudio@sfstudio
2 881 Сообщение
Wi-CAT
#3 · 13/08/2020, 23:09

Если нет DHCP в сети, то логично что в настройках LAN должна быть снята галка получения параметров по DHCP и адреса каждой АП заданы руками фиксированно. Отсюда и потеря доступа. Либо задавайте руками, либо DHCP. Если оставить DHCP, а сервера не будет в сети, то при следующем запуске логики получите перезд роутера в Zeroconf подсеть. Если склероз не мучает.

Остальное попробую проверить на следующей неделе. Сейчас увы возможности нет.

Раньше не выйдет ;(

Ilya_SA
Ilya_SA@ilya_sa
45 Сообщений
#4 · 14/08/2020, 00:27

Прошу пояснить туповатому мне ситуацию, которая похоже Вам кажется нормой, а мне не понятна. На примере этого кейса, где это хорошо видно.

Вот есть примененный конфиг, успешно работающий в части доступа к ui. Далее мы делаем незначительные изменения, допустим радио косметически правим, применяем и получаем недоступность ui. Делать нечего, перезагружаем, и опять все норм, только что сделанные изменения сохранились, и они уже почему то не препятствуют доступу к ui.
Так как же ошибки в настройке LAN (например dhcp) могут то влиять, то не влиять, и это будет нормальным проявлением?

Какова вообще концепция сохранения настроек и их применения?

Еще призовой вопрос - как произвести все нужные настройки разом, не дожидаясь выполнения переинициализации всего хозяйства после каждого дискретного изменения? Вот например изменить LAN и задать пароль wifi.

Последний раз редактировалось 14/08/2020, 00:28 : Ilya_SA
termit
termit@termit
52 СообщенияАвтор темы
#5 · 14/08/2020, 00:31

Хм. Да, дело было в галке "try dhcp" . Но,  с установленной галкой, при подаче питания ведь он берёт настройки LAN с соответствующей вкладки, если не может получить по dhcp, что логично. А при применении изменений,  он эти настройки уже игнорирует, и если не получает корректных по dhcp, то использует autoip. Это фича?

По поводу срочности - не горит...

termit
termit@termit
52 СообщенияАвтор темы
#6 · 14/08/2020, 00:37

Да, дело в том, что если бы алгоритм присвоения адреса в случае невозможности получить по dhcp(при установленной галке "try dhcp")  был конкретный: или autoip или мануальные настройки всегда - было-бы предсказуемо. А так - я что-то и не сообразил, что по разному он себя ведёт при холодном старте и при применении настроек.

termit
termit@termit
52 СообщенияАвтор темы
#7 · 14/08/2020, 07:05

На правах брюзжания)) :

Может тогда галку, в настройках LAN, следовало-бы переименовать в "Use DHCP", вместо "Try use DHCP", а поля статических настроек затемнить, ибо они становятся не актуальны(правда не сразу), ибо иначе путает - ведь мы понимаем это как "попытаться использовать DHCP, а если не получилось, то статика", а получается "используем DHCP в любом случае".  Но лучше, конечно, чтобы алго был именно такой, что если получить по dhcp не получилось, то используются статические, а вот если и статические не заданы (правда веб UI так сделать не даст, но вдруг у кого-то получится), то тогда auto ip.

Последний раз редактировалось 14/08/2020, 07:09 : termit
termit
termit@termit
52 СообщенияАвтор темы
#8 · 14/08/2020, 08:53

Или предупреждалку некую, просьба, написать, что именно при "при следующем(1й после powerup не считается) запуске логики получите перезд роутера в Zeroconf подсеть". Вобщем, для "вантузятника", коим я являюсь, сие поведение не очевидно.

sfstudio
sfstudio@sfstudio
2 881 Сообщение
Wi-CAT
#9 · 14/08/2020, 12:49

Да я тут уже думал как лучше сделать, но оно всё имеет побочки. Сейчас логика аналогична одной энтерпрайзной железяке.

Благо основной кейз это роутер с DHCP+несколько AP, в роутере в NetDiag видно куда АП занесло по адресам.

 

Последний раз редактировалось 14/08/2020, 12:51 : sfstudio
sfstudio
sfstudio@sfstudio
2 881 Сообщение
Wi-CAT
#10 · 16/08/2020, 17:07

Так. Логику AP DHCP переделал, убегать в zeroconf будет только если адрес занят и отвечает на арпинг. (будет в следующей версии).

С WDS вижу траблу в 5ГГц. Драйвер не регистрирует wdsi* интрефейсы, буду посмотреть. В 2.4 проблемы быть не должно, но не проверял пока. Разберусь почему в DBDC режиме 7615 не регает 5ГГц интерфейсы для WDS тады проверим.

Остальные устройства т.к. не в DBDC режиме работают а имеют отдельные чипы по бэндам проблеме не подвержены.

termit
termit@termit
52 СообщенияАвтор темы
#11 · 16/08/2020, 22:27

Пысиб, ждём.

sfstudio
sfstudio@sfstudio
2 881 Сообщение
Wi-CAT
#12 · 16/08/2020, 23:12

Пока не за что. WDS в DBDC оказалось недопиленным. Автотесты поправил для проверки. Надо либо реализовать самому (поддержку dbdc для wds) что проще, но сейчас загрузка под завязку. Либо пнуть китайцев (MTK) ибо их косяк и пусть пилят. Тем более для 7915 судя по всему это уже сделано.

Сейчас там тупо в WDS кто был default band то и будет.

Думаю поступим так, пнём китайцев, если до момента как освобожусь не пришлют обновление дров - знач сяду и сделаю свою реализацию. Вот уверен что это уже поправлено, но по какой-то причине опять таки затягивают резину с доступом к >5.0.4.0 для 7615..

В общем переадресовал коллегам, будут разбираться.

termit
termit@termit
52 СообщенияАвтор темы
#13 · 17/08/2020, 10:38

Окей. У меня горячки нет, если что.

А пока погоняю дальше разные галочки-крыжики...

Если вы нашли ошибку, пожалуйста, выделите фрагмент текста и нажмите Ctrl+Enter.

Сообщить об опечатке

Текст, который будет отправлен нашим редакторам:

Отправить